How to make slopes on the doors

After you installed the door, safety is guaranteed. Also, tenants of the house will be reliably protected from annoying sounds coming from outside. Yes, and heat losses are reduced to "no". But there is one "but". At first glance, a naked concrete rushes on the doorway, a naked concrete is thrown in the eye, unfeaming bricks and fasteners are visible to which the door frame was installed. Therefore, this site requires the creation of a product that successfully disguises the consequences of editing. Consider ways of finishing the slopes of the entrance door.

1
Functions of Distance

The main function of the slope is the extraction of the opening. Door slips are designed to mask fasteners with which the doors were installed. In addition, this design increases the stability of the door to hacks. And besides, without a slope, any door, even made from the most expensive wood, will lose its attractive look. Popular methods of formation of door slopes: plastering, installation of drywall, installation of slopes, made and plastic, wood covering, laminate or MDF.

2
Preparatory work

Before switching to the main part of the discovery, the surface must be prepared correctly:

Close the doorbell in order to protect against damage to the polyethylene film by fixing it with scotch. Do the same with the door frame.
First, it is necessary to combat the protruding parts that interfere with the mounting of the frame required for the suspension of the slope.
Remove the dust from the surface and properly penetrate it. If you are dealing with walls built of foam concrete or any loose material, you should use the surface primer.
Lay the power cable required for the lamp switch. But if the skeleton fastening is assumed, the wire is laid after installing the frame.

3
Walking the door slope

The method of plastering the slope is simple and economical and is as follows:

Install the beacon profiles to make it easier to remove a flat surface. For fastening beacons, a gypsum solution is used, which is well seized.
Position mayakov Adjust using a bubble level, and wait until the solution is hardening under them.
Fill the slope by cement-sandy solution, for the preparation of which 1 part of the cement is taken, 4 pieces of sand and a little plaster. Celma and spatula are used to apply mass.
Next, it is necessary to cut the solution for lighthouses.
Metal corners are used to create smooth angles, which are sitting on plaster.
After drying, the solution is applied starting and finishing putty.
The dried coating is polished with the help of an abrasive mesh before getting a smooth surface.
At the final stage, the slope is covered with coloring composition.

4
Plasterboard slopes

Sunsaws made of drywall sheets perfectly solve the problem associated with irregularities that are present on the surface do not need preliminary alignment, do not require the frame assembly:

Trunking the walls, you need to wait until the primer dries. Meanwhile, the sheets should be cut. It is recommended to take into account the location of the doorway and its possible SCOS.
When the slope dry after the primer, start the installation of the panels using the dowel to attach.
In addition, it is possible to fix the sheets with special glue, which will provide a smooth installation of drywall, covering glue all the surface or point, withstanding a distance of 15 cm.
It is started to mount the gypsum sheets from the side panels, the top is finally separated.
When the work on the fastening of the GLC is completed, the joints should be sharpened, and the corners are created using perforated corners.

5
Plastic slopes

The plastic is crucified more often by window slopes, and for doors it is used under the condition of the interior decoration from plastic:

After preparing the slopes, cutting plastic should be engaged using an electrolovka to get the edge that has a smooth surface.
Spend a trial laying of the panels to rate how exactly they fall, and welcome in size. First of all we are wearing the side panels. Then we are finished top.
Confirm on the screws starter profile to the box and install on the edge of the wall using a dowel, a rail to which the panels will be attached.
Dress up on the bottom of the slope plug. Barpim panel in start profile and side slope.
The upper slope is sewn similarly.
At the final stage, the formed seams are covered with silicone.

In addition to ordinary PVC panels, a sandwich panels are used for decoration, in which there is a layer of insulation between the two sheets of plastic.

6
Towes from wood

When finishing door slopes, wood remains a popular material, as it successfully harmonizes with a common interior of the room:

To cover the surface, laminate or MDF board is used. The choice in favor of a certain coating is made, depending on the width of the discovery of the slope.
Carefully seal the seams formed between the door and the wall. After compulsory, remove the excess foam.
At the next stage, the surface is cleaned and ground.
First make the top slope, then the side.
Determine how the slopes will be located. They can be parallel to the wall. It is also possible to make a small corner of the letter "l". In the case of parallel slopes, set the rack equal in the thickness. If conduct mounting under angle, then rail near doors should expand, a second near angle – narrow.
Dowels are used for fastening the carriers, for wooden - glue or self-tapping screws. Decorative plugs apply for masking hats.
Treat the seams with colorless silicone sealant and check the corner around the perimeter.

7
External slopes

Work is carried out in such a sequence:

To begin with, the clearance formed between the door and the wall. When the foam freeze, cut her surplus.
To check the gap purge, use a lighter: carry a burning product by profile and see if the seam does not sway. If the flame moves, sewer the plot again.
Close up of seams with cement. Putty and plaster will not fit.
When the cement mixture is grab, you can install platbands, fixing them with special brackets. They are needed not only to hide the gap, but also the protection of the pins from hacking.
Sunsowing, located on the outside, also close the cement, clearing the surface pre-from the old finish, garbage and dust and processing it.
After drying the primer composition, the cement layer is applied, and the walls are aligned.
At the final stage, painting external door sluts or any other finish is performed.