In most urban apartments and almost all country houses floor wooden. It is usually placed by simple or tanted boards. But over time, the boards come into disrepair.
How to Align Paul Wood - Causes of Defects
The reasons for the appearance of defects in the outdoor coating:
- The operational properties of wood will deteriorate over time. And this aging process cannot be prevented, you can only slow down.
- In the process of laying the floor, technology was broken.
- After laying the floor there is a natural shrinkage or a drying of a tree. At the same time, the overall dimensions of the board, albeit in small limits, change. There are gaps between the boards.
- With significantly increased air humidity in the house moisture, wood is actively absorbed, which leads to an increase in the size of the boards, and subsequently to their rot.
- Not a small value is fixing the germ boards on the lags. If nails are fixed unreliable, then during operation, they are loosened and outward, which leads to the destruction of the design and the screen.
How to align the wooden floor - replacement of boards
Digitable and poorly preserved boards are subject to radical replacement. To do this, you will have to disassemble sexual coating, including the draft floor. Before disassembling the board should be marked, for the correct assembly. According to them number. The discharge board is replaced similar to the type of connection. After laying the genital boards back to the lags, they are fixed with self-draws or wrenches.
How to align the wooden floor - fixation by self-drawing
Drumped holes in a blackboard with a diameter of 2 mm, screws twisted. The hat is treated. If the screws with a hat for the outer attachment, then the hat is cleaned. Then the hole is sweeping. The length of the screws is less than the thickness of the board together with the lag at 20-30 mm. Fixing occurs at least 2 self-pressing, and preferably along the entire length equal to step.
How to align the wooden floor - fixation with the help of a wanking
The length of the wrenches is 100 mm and the diameter is 10-12 mm. Several holes are drilled by the electric drill at a distance of 100-300 mm by the diameter of the dummy. Further, the seeds are clogged into boards and lags. To prevent their falling out during operation, use joiner or PVA glue.
After the shrinkage of wood, the floorboards begin to publish an unpleasant creak. And the longer it is ignored, the stronger it becomes.
How to align the wooden floor - how to remove the creaking between the boards
Several tips How to remove the creak:
- in the slot, where the boards rub, you can float a mixture of graphite powder with a talc. After all, it is known that graphite is used as antifriction material;
- with a small wear of the genital boards, they are wedged with wedges to eliminate friction among themselves. But if the wear is significant, it will not give a special effect;
- drilling a small hole in the place of the greatest screen, the space between the boards and the slab of the ceiling is filled with the mounting foam. When expanding and solidifying, it fills all the cracks, which leads to the elimination of mobility and as a result of the screens. But it should be borne in mind that the mounting foam is not very durable material.
How to align the wooden floor - eliminating the slots
The slots between boards and scratches can be eliminated by putty. If necessary, in construction stores, you can pick up the color of the putty in the tone of the genital boards. After the work carried out, the floor is aligned with sandpaper and covered with paint or varnish.
How to Align Wooden Floor - Plywood Cocking / Fiberboard
When aligning the floor, without making cosmetic repairs, it is worth considering the firmware method with sheet materials, such as plywood or fiberboard. Plywood is selected moisture-resistant thickness of 12 mm or more, the DVP is laminated with a thickness of 5 mm. The fixing is made on the screws in 150-200 mm increments.
Using a laser level it will be necessary to make markup. Next, beacons are formed from the self-samples (check the level of installation). Phaneur is in advance to be cut into equal parts and stacked as a brick, with a displacement. Further, the plywood is attached to the lags with self-tapping heads.
As you can see, the alignment of the floor does not require special skills. All work must be accurate and rechecked by the level to become really even.
0
1256
