Making modern repairs in the kitchen, it is difficult not to think about creating a bar counter. Although many designers leave the stereotypes and place the bar racks in an absolutely any part of the apartment or at home. The fashion trends of this detail of the interior will make the interior decoration not only beautiful, but functional.
1
Before the direct creation of the bar rack, it is advisable to draw a sketch on paper, decide on the materials. It is necessary to repel from the fact that usually the tabletop is located at an altitude of 110-120 cm. The size of the table top also depend on the area of \u200b\u200byour apartment and in the standard variant are 30 cm in width and 1 m in length. Materials use very diverse: wood, metal, plastic, glass, natural or artificial stone, as well as their combinations. As a base, you can build a frame from metal products, to strip it with plasterboard and bind to your taste. However, in most cases, the framework performs a glued and twisted wooden timber. He has a sufficient margin of safety, moreover, the material is natural.
2
It is necessary to think through the presence of lockers under the tabletop, their size and quantity. It is necessary to take into account the possibility of placing a footrest. The main rule for the convenience of the bar rack - the tabletop should cover the lower lockers and the footrest with the margin so that you can learn and do not sit kneel.
3
Very comfortable Bar rack combined with a working surface. One side is facing the kitchen, it is at the same height as other surfaces, it is convenient to prepare cocktails on it. The second side that is facing the living room is used to use these drinks and sometimes food. The add-in over the tabletop can be used to place the rails, which will hang wine glasses, hoods, which eliminates unpleasant odors or tobacco smoke, lamps and light points.
4
Often a bar counter with one side borders with the wall. The wall decorate the favorite photos within the framework of the attributes of football teams or fasten an additional cabinet.
5
So, to create a bar rack from a bar need:
Wooden timber;
LDSP or plasterboard;
Selflessness, nails;
Glue;
Countertop;
Edge;
Hacksaw;
Screwdriver, electrolybiz, drill;
Corner and level;
Sheds;
Chrome-plated stand.
6
Depending on the length of the future rack, the bar saw the timber - 4 parts. They will be longitudinal beams. The following saws are four end beams that will be responsible for the width. Supplements for a tabletop of 2 meters long enough to make eight: 4 in the corners and 4 in the middle, on an equal distance from the center. The length of these beams determines the height of the bar counter. Having exhibit the design and pre-engaged it with nails, check the maintenance of the direct angle and the levels of horizontal and vertical planes. Before twisting all the beams, self-pressing vessels are desirable for glue. This will harden the design and will save the finished product from creak.
7
After drying the adhesion, it is possible to mount the frame to the wall and proceed to the wrapper of the LDSP. In the case of placing on the bar, electrical equipment with the fastening of wires on the trim, LDSP is better replaced by plasterboard. The material to cover plasterboard on the bar stand can be the most diverse - it all depends on the design preferences and financial capabilities. Now you can go to the tabletop. The finished tabletop can be ordered on a furniture factory. It will make any geometric shape according to your desire and wake the edge edge, will only be screwed. However, if there is a desire to save and then, then you need to buy a chipboard with a thickness of 20 mm with a moisture-resistant coating, place the boundaries and remove the electrical border with an extra charge, independently stick the edge using an iron. The tabletop is attached by self-drawing from below. The length of the self-samples must be calculated so as not to make through holes.
8
From above, we install chrome-plated racks, fix the chipboard. Next, set the rails and lighting equipment. The height of the superstructure should allow freely hanging glasses on the rails. Fresh canopies on the open part of the frame and install the doors. Foot stand Breep to the floor at a distance of 10 cm from the frame. Bar rack is ready - you can mix a cocktail, sit on a high chair and testing creation.
Taking advantage of the creation of a bar rack a little time and not quite a lot of funds, an element of luxury and one more place for a pleasant time in a circle of friends or family appeared.
How can a self-respected master work with Tristone stone? Really only lose reputation and customers. Believe me, there will not earn money there especially
0
1173
And I first wanted to make from drywall or chipboard, but the low-budget version of the bar rack was caught, which can be collected from the modules.
How can a self-respected master work with Tristone stone? Really only lose reputation and customers. Believe me, there will not earn money there especially