How to mount plasterboard

Plasterboard is the most popular and popular finishing material. With the help of drywall, it is possible to align walls and ceilings, as well as make your highlight in the design of the room. The material is not capricious, it is easy and easy to work with it.

1

How to mount plasterboard

To repair your own hands to repair in a house or apartment, you need to prepare not only tools and buy all materials, but also understand how to work properly with these materials.

Methods for fastening drywall:

• Frame.
• Frameless.

The first option is complicated, because you first need to create a frame - this is the base from a metal corner to which plasterboard will be attached. Work is not a special difficulty, if you explore all the nuances. Naturally, such a way more work at the initial stage, when you need to build a frame. But when attaching plasterboard no problems will arise any problems.

The second method is faster, because plasterboard is attached to the wall or ceiling directly on a special adhesive solution.

2

How to attach plasterboard. Frame method

The method is expensive, if compared with a frameless way, but in this way it is possible to improve the soundproofing in the room, align the walls (even if the decent difference) and do not need to prepare the surface. You can also use this method if the walls are cold and frozen to create an additional airbag.

The frame can be done both from a metal corner (galvanized profile) and from a wooden bar. The second option is not entirely reliable, especially if indoors are wet and cool. A tree can deform with time.

To work, you will need such a set of tools plus materials:

• perforator and screwdriver;
• spatula for ochpakliding of walls, trimmed by plasterboard;
• scissors for cutting for metal;
• as well as plasterboard, metal profile, suspensions, self-tapping screws, dowels and screws.

The order of work is:

• First you need to perform measurements, make marking for fastening the suspensions and the profile.
• The guide profile is attached around the perimeter of the room in such a sequence: the upper and lower to the ceiling and the floor, the side on the right and left to the wall.
• In the guide profile you need to attach the bearing elements in 40 cm increments, they are attached to the wall on the plumb (step - 80 cm).
• Mounting metal frame: mounting to the ceiling and floor on screws and dowels. We recommend using the building level.
• After completing the installation of the frame, you can mount plasterboard. If you want to warm the room, then the insulation can be laid between the wall and plasterboard. For example, Minvatu.
• The plasterboard is screwed to the frame on the self-tapping screw (length 25 mm), to fasten each self-tapping screw to the deepening of the Hat 2 mm.
• After completion of the work, all the joints and the entire surface of the trimmed walls or ceilings are plasterboard, you need to be ochpace. It is enough to apply a thin layer of finishing putty, and after drying, it is cleaned with a fine-grained skin.

3

How to mount plasterboard. Frameless method

The second method is simpler, only it is necessary to take into account that for this method of the wall should be smooth, durable and without damage to the fungal mold, not freezing, without paint, wallpaper.

Materials and tools:

• spatula plus putty;
• plasterboard;
• dry mix dry mix;
• lobzik, Knife construction, rubber hammer, roulette, level, fishing line and rule.

How to attach plasterboard to the wall:

• The surface must be prepared in advance: clean from dust, remove old wallpapers, treat the primer mixture. If you need - put a putty to a thin layer.
• Perform the measurements of the wall, cut down the gypsum meters. If the ceilings are not standard, then you need to dock with pieces of drywall. Therefore, cutting material is performed at the initial stage.
• How to cut drywall: a conventional construction knife, sufficiently cuttingle cardboard from the front side, and then break the sheet along the line to cut the cardboard from the wrong side.
• If a figured clipping is assumed, then the electrolybiz will be needed.
• The gypsum washes according to the instructions, the glue is applied to the entire surface of the sheet with a toothed spatula, it is possible to point if the walls are perfectly smooth.
• The sheet is glued to the wall, pressed the rule and according to the rule you need to knock the rubber hammer.
• The seams between the sheets of drywall 5-7 mm, we leave 5 mm from the floor, from the ceiling a maximum of 10 mm. After drying the adhesive mixture, after drying the adhesive mixture, closed by a plinth or apple.