Insufficient operation of the cooling system of laptops, especially when working with Internet resources, can lead to the failure of the device or even damage. Solve this issue is possible, acquiring in the store or independently making a special desktop stand for cooling the laptop.
1
To begin with, it is necessary to draw a sketch of the product in the original size that we are going to do. Linear dimensions of a manufactured stand must be a little more dimensions of your laptop. You should make a clear markup, where air intakes will be located on the stand. They should be located under the air intake holes of the bottom panel of the laptop.
2
The further stage lies in the transfer of the sketch to the material from which you are going to make a stand. This can be done using a copy of the appropriate size. As materials you can use wood, thick plastic, aluminum sheets, as well as plexiglass. The structural stand should consist of six parts: the upper and lower lids, as well as four side, the dimensions of which should be a little exceeding the size of the cooling fan.
3
Cut out the details of our design, for this it is convenient to use the electrolovka with the tooths of the saws, corresponding to the materials that we will apply. With the help of the same jigsaw, drink cooling openings of the top cover to install the fans.
4
Sketch of our support can also be drawn not on paper, but immediately on the top item of our product. To mark the fan sweatshirts should be placed on the cover working from the laptop network. We note the heating places of the upper cover. We supply them with a reserve of several centimeters. Lobzik with a sawn, the teeth of which are suitable for our material, cut the air intake openings of the cooling. The uneven edges and burrs of our openings are processed by a file and emery paper, seeking perfectly safe edge.
5
In the side wall, drill a hole for the output of the wires. We need to withdraw the power wire of the laptop, the mouse wire, it is desirable to connect the laptop to connect the USB extension. This hole should also be cleaned and desirable to glue its edges with soft rubber or foam rubber. The stand is collected using self-tapping screws. For this purpose, it is convenient to use a small screws of a small size, with a head under the crusade screwdriver. The edges of the metal sheets are rejected at a right angle, their mounting between themselves occurs with special fleets of metal. If the stand under a laptop is made of plexiglas, then its details are sitting on glue. For these purposes, it is advisable to use tight fit adhesives, for example, epoxy resin.
6
When the framework is ready, we can do its internal device. The fan is more convenient to attach to the top of our product, using small screws or glue for this. As glue, as when assembling the support parts, it is desirable to use an epoxy resin. The next stage of our production is the assembly of the electrical fan circuit.
7
It is desirable for convenience in the operation switch to put on an electrical cable, a few centimeters from the edge of the output. Before soldering the elements of our chain, it is necessary to check the performance of the schemes collected by us. To do this, we carry out the cleaner of the elements, after which the seats of the twists are wrapped with a tape. If all the elements of the electric chain assembled by us are operational, disassemble the twists and install with the soldering iron, solder and rosin. When using multiple fans, an electrical circuit of a parallel connection is used.
When the stand is technologically ready, it works great, it is necessary to give her a more aesthetic look. For this, the whole dirt is cleaned with a soft brush, with scissors, the details of the sketch are cut on the self-adhesive paper, and in them the desired hole, the stand is pasted. With special accuracy, the sharp edges of our stand should be placed, this will prevent possible injuries with further use of the product.
Thanks for the detailed description, I will definitely do it yourself. I was looking for an example from the tree, categorically against plastics, and metal all the same heavy. I saw a table for a laptop Laptop Sititek Bamboo from Bamboo, I really liked, I want to do this.
0
1881
Thanks for the detailed description, I will definitely do it yourself. I was looking for an example from the tree, categorically against plastics, and metal all the same heavy. I saw a table for a laptop Laptop Sititek Bamboo from Bamboo, I really liked, I want to do this.