The cooling system of the laptop is equipped with a cooler. The ventilation device not only provides cooling processor, but also draws dust. Putting dust on the internal details of the system in the process of full use contributes to braking, freezing residential Programs and termination of the device's performance. Cleansing from dust can be both superficial and in-depth.
1
Consider the first method that is designed for an initial and mid-level user. First of all, do not forget about the warranty period: if the laptop or ultrabul New, then independently embedded inward, use the service. Warranty obligations, in the event of a breakdown, are possible to execute if the factory seals are not violated. If you notice that the device in the process of operation becomes hot in some places - contact the service center in order to fully clean the laptop from dust. After the warranty expires, use the Council below.
2
Prepare the following instruments and fixtures:
screwdriver To remove the back cover of the laptop;
compressed air in the canister (if find on sale in your city);
pure stable surface for disassembling and cleaning the device;
soft, fluffy brush;
cotton buds .
3
Move the mode to the "Exclusion" process. Disconnect the device from the network, remove the battery. Lost fasteners Bolts of the rear panel. Note that the bolts often hide behind rubber legs, stickers and fuses. If the lid is ne. give in placeSo, not all bolts are unscrewed and you should search for others on the sidebar. Some models except bolts are fixed latch. When all the fasteners are disconnected, remove the cover, more often it is shifted to the side. If the panel is ne. give in place, more Once check if all the bolts are removed from behind.
4
Let's proceed to the removal of large garbage in the form of dust lumps, on the radiator and cooler. Preferably, the cooling system is connected to the video card chip, radiator and processor copper tubes. Large, clear garbage clean with cotton chopsticks or remove the tweezers. After use a compressed air cylinder. Perform cleaning carefully and slowly, so as accidentally do not move and not bend ribs radiator I. heat harvested Tubes. You can clean the cooler with the same canopy, performing short pressing. Do not allow the actively rotation of the fan blades, it may have negative consequences. Keep a balloon strictly vertically.
5
After how you removed dust from the main working parts of the device, you can blow up other open parts of the system. After the work done, make sure that all the loops remained on the spot, the details are not shifted and not broken. Take the lid, set the starting position and screw the bolts. If at the opening you had to remove the legs, then be sure to stick them into place. The gap will allow air to circulate between ventilation holes.
6
Now consider the second way for more experienced users. Deep cleaning and improving the conductivity is particularly relevant if your laptop is turned off in the process and pulling Gul. AT dann Case It is necessary to remove some details, replace the thermal paste. In addition to the above-mentioned needed tools, add: unnecessary discount or credit card, smooth fabric without a pile, one hundred percent alcohol and thermal paste. Remove the laptop cover as in the first case.
7
Remove the radiator. New models are equipped with a single radiator for cooling the video card and processor, from which the branching of copper tubes to the fan are running. The processor, video card and cooler are attached to a few screws - remove them. Remove the cooling system in the aggregate. Often you have to make an effort, since there is a thermalcaste below, which is yourskind fastener on a sticky basis. If the details are not amenable, try them to move them to the sides.
8
It is better to perform similar manipulations after the active operation of the device, since the thermal machine is heated and becomes fat. If there are several radiators in your laptop, then you should perform such actions for everyone separately. Clean the details cleaned with compressed air, and then beware of the plastic card an old thermal chaser. In no case do not use metal items: the slightest scratch will not only aggravate the situation, but also fail the cooling system.
9
After Cleaning the layer Thermal Paste Apply the alcohol to the flaps of the alcohol, and we remove the remainder of the paste. Do not touch the surface and avoid moving garbage. Remove the thermosmad from the video card and the processor with the flap of the tissue impregnated with alcohol. Make sure that the fabric is not too wet, and the drops of alcohol did not hit the motherboard. Remove dust from the details should be cleaned the thermosmars. After wet processing, avoid touch and getting garbage. Let's proceed to apply the thermal paste. Singing a small drop of lubricant to the center of the chip and distribute according tothe top of the edge of a pure plastic card. The thermal layer should be moderate, do not overdo it.
10
Apply a translucent layer to the surface of the radiator, because it is in contact with the cooled chip. Install the details in place. Try to get into the grooves from the first time. For this, do not hurry and install the radiator very carefully. If you smear the thermal column on the edges of the chip, you have to Remove the details and start the process from cleaning the thermal paste, performing all previous operations again. When the cooling system is installed, slightly push hERE and slide horizontally back-ingestd. D.la provision Contact. Return to the place of screws, tighten them gently, performing turns. Replace the laptop cover. Finally, blow the connectors and keyboard with a vacuum cleaner.
Clean the laptop from dust depending on your qualifications. Do not retreat from the proposed instructions and act intuitively. If you are subject to an important detail, violate the contact or cherknet Scratch, then the efficiency of the device may worsen.
0
7813
