Beginner masters when repairing its apartment think that wallpaper sticking is a common thing, and everyone can cope with him. But dare you to upset, high-quality and professional pasting wallpaper has many stages that we will talk about in our article.
How to glue paper wallpaper properly - prepare the room
Before starting work with wallpaper, it is necessary to clean the walls from the previous coating. If you have been pasted vinyl wallpaper, you first remove their top layer with the spatula, and you can skip the remnants. When the wallpaper was adhesive, the joints are smoothly cut and stitched.
- If the wall has bugs and cracks, align the irregularity with putty or plaster. At the end of the work, pass the primer, then the new wallpaper will be lying smoothly and beautiful.
- If the former coating was glass windows - rinse with a solvent with a wall, then swipes and priming the overall surface.
- To remove textile wallpapers, you need to handle the wall by a versatile agent designed to shoot wallpaper. As a rule, it is with this kind of problems there is no problems, and you can easily remove them manually without resorting to various tricks.
- When you decide to apply the wallpaper, where there used to be paint - it is necessary to remove the paint with a special solution. Then the wet paint is squaring with a spatula, and the remaining part is covered with a smooth layer.
- Walls made of fiberboard, chipboard and drywall are pre-ground and grind. Special attention is paid to the joints of the plates and holes from screws and nails.
How to glue paper wallpaper properly - cut wallpaper
After you have prepared the wall to the wallpaper pasting, proceed to cutting the roll. It is advisable to have an assistant in this case.
- First step, check that the sized wallpaper numbers have the same values. Also look in the guidelines for wallpaper, how best to glue this type - in the joint or brass.
- The height of the wall measure the roulette, and mark the measurements with a pencil. Add 5-7 cm reserves to the measurements.
- For convenient cut, prepare a luggage knife and a metal line.
- Singing at once and cut from 5 to 10 bands.
How to glue paper wallpaper properly - weigh glue
Work is performed by one person, without any difficulty. The main condition for obtaining a good result is the observance of the rules without a sequence. The glue is recommended to purchase for light wallpaper, the usual preparation is made as follows:
- Pour cold clean water into the container. To breed the average pack of glue, you will need about 5-7 liters of water.
- Gradually stirring, pour glue.
- Mix well the resulting mixture and leave to swell for 10-15 minutes.
Ready glue should not have a liquid consistency and lumps, to get rid of the latter, mix the glue, pressing lumps.
How to glue paper wallpaper properly - process glue
This type of wallpaper has a feature to rush after the glue hitting it, so all the work do neatly and carefully.
- The wallpaper must be deployed on a flat and clean surface - a table or floor.
- It is recommended to apply glue with a roller or a wide painting brush, controlling the absence of dry places.
- In order to avoid hitting glue on the front, take the edge of the strip and fold it to the middle, repeat the procedure from the other edge. Next, fold the canvas twice.
- So that the glue absorbed the band for 4-5 minutes. During this time, wake the wall glue on the width of the wallpaper.
How to glue paper wallpaper properly - wallpaper glue
- Wallpaper start gluing from the top line of markup, gradually turning over the entire length.
- Next, you need to smooth the glued strip, use a dry cloth or rubber roller for these purposes.
- Smoothing is carried out in the form of a Christmas tree - imagine that the roller you draw a New Year tree, moving from the middle to the edge, pursuing every branch. We get rid of these movements from air bubbles and align the surface.
- To glue the following cloth into the joint to the previous one - attach the strip to the edge of the already plated strip. Especially carefully postpone the edges of the bands at the junction and remove the excess glue from the front side with a dry cloth.
After sticking the wallpaper, wait for them to complete drying, and only then proceed to excess circumcision. Cut unnecessary edges with a stationery knife.
0
605
