How to clean the sewer

How to clean the sewer

The need to clean the plumbing pipes occurs periodically in any house. After all, in the inner walls gradually fatty deposits, food residues, hair and other trash. It turns out that it is possible to compete for pure drainage by available methods without resorting to the help of specialists.

1
Initially, you need to determine the location of the blockage. If water is stood only in one plumbing device, the trash plug was formed in its discharge. And when water rises from all the plots, clogged, it is a rather serious problem.

2
Neutralize the blockage is capable of boiling water. Fill a 1-2 liter of hot liquid into the scored pipe, and it softening internal sediments. If the block is partial, this method will work perfectly, and do not have anything else.

Unnamed turniooylgp

3
Strengthening the boiling water is capable of such remedies, like soda, salt and vinegar:

  • A glass of food soda pour into the wastewater, and then pour 3 glasses of boiling water. An alkaline medium will appear in the pipes, which breaks fats and small garbage.
  • Send inside the sewage sewage of Soda and as much vinegar, close the plug hole, leave for 2 hours. As a result of the chemical reaction, a bulk foam cleaner is formed. After that, get the plug and pour the liter of boiling water.
  • Push up in stock 100 grams of salt and soda. Fill with boiling water and during the next 8-10 hours do not use any sewer.

4
Alternative to folk remedies - chemical compounds for cleaning pipes offered in stores. Despite the differences in price, and familiar to everyone "Mole", and German tubes with rapid names will be cope with the task almost the same. Often, you just need to pour the solution into the pipe, and after a certain time the block will eliminate itself. When using household chemicals, it is important to clearly follow the instructions of the manufacturer, work in rubber gloves, to ventilate the room well and comply with all precautions.

5
Any of the above methods is well complemented by Vatuz. Dial some water into the sink. If you brush the bath drain, close the overflow hole tightly. At the angle, get the Vanutuz into the water, press it to the drain, make some swing movements. Then dramatically tear the tool from the plumbing device. Most of the garbage should go out, after which it is easy enough to remove.

6
Particularly dense bed can be eliminated using a special cable. There are various nozzles that allow you to get rid of any garbage: if one tip did not cope with the task, another necessarily remove the deposit. Take the cable handle, and get the other side to the drain hole. Gently promoting the steel rope inside the sewerage, rotating it clockwise. Do not rush to not damage the joints of the pipes or their bends. When the tip of the cable gets to break, you will feel the resistance. At this point, you need to increase the intensity of rotations to push the trash cork. If you use a hook nozzle, pick it up and pull it out.

Slores that often occur in the same place indicate an incorrectly mounted knot of the drain system. It is necessary to find a problem area and collect it more correctly. And when the obstruction of the pipes you find in different places, you should check the angle of inclination of the sewer tube. A large angle provokes the accumulation of deposits on the entire inner surface of the walls, and a small one on their bottom. Both of these situations can be corrected only with a complete reinstall system.

Comments leave a comment
Michael 07/02/2016 at 1:59.

Bought a specialtross 14 mm, because Clean the pipe 110 mm by a domestic cable of 9 mm with a "pork tail" and the handle could not be possible. Vomor at a distance of 3 meters from revision (where the cable can be launched) and on the way to it 2 rotation by 90 degrees, made by 4 corners of 45 degrees. So, the cable of 14 mm with the Natchadshnik did not give any result, because Due to the flexibility, the impact force for a zoom was practically not transmitted. Almost instant result was achieved as follows: 1). shoved the cable into the sewage to the ground; 2). cut off the watering hose by 10 cm shorter cable (the cable was 4 meters, the hose 3.9 meter was cut off); 3). Made the rope conductor in the hose (for which they first missed the wire-twisted pair through the cut hose, tied the rope to twisted pair and stretched out, stretching her rope through the hose); 4). Tied the rope-conductor by the end of the cable sticking out of the sewage system and began to plant the hose (one-alone, the hose running on the cable into the sewer, the second- helped and pulled the conductor). The hose went into the sewer in the cable, almost like on rails. 5). 5-6 reciprocating movements of this design and no blockage! Summary: The same could be done with a 9 mm with amateur cable (only a pen for rotation to bite off). Specialtros 14 mm * 4 meters bought for 1900 rubles., It was possible and not to buy. Yes, if you can also be asked after 5-6 reciprocating movements and removing a blockage, I recommend to make another 10-15 of the same movements, and then rinse with hot water, there is no trace left.

To answer

Add a comment

Your e-mail will not be published. Mandatory fields are marked *

close