How to make sewage in the country

How to make sewage in the country

To make high-quality sewers with their own hands, it will take a lot of time and labor. But the owners will save finances. Of course, professionals cope with this process much faster, but their work is estimated to be expensive. But we are more interested in how less invest in this case. Make the sewer in the country is not so difficult, for this no particular engineering practice is required. It is enough to do everything at the plan below.

1
First select the location where the sewage pit will be located. It is best when it is placed in the area of \u200b\u200bthe Nizna. Then the bias of the pipes are provided by itself. More to choose a place:

  • Characteristic of the soil on your site.
  • An indentation from the country house. It is impossible for the plums to be near the construction. It is allowed to distance not closer than five meters to the object.
  • Do not make a hole near plumbings, fences.
  • It is necessary that the sewage is in an affordable place. In case of need, transport will be able to drive up to her and pump out feces.

2
To determine how many pipes, corners, adapters for draining in the country house, will need a scheme. Make it easy. Consider all the objects inside the construction (shells, bathroom, toilet) that require a removal. Then calculate the amount of the required material for the sewage outside.

3
Deciding with the plan, proceed to the purchase of material. We will need:

  • Siphons Plastic for shells and bathroom.
  • PVC pipes different diameters for internal and outdoor work. Cross To connect several drain points into one common pipe.
  • Sand, gravel, cement, Concrete mixer.
  • Round floor slab and hatch.
  • Septic, Concrete rings (sizes: 1 meter by 90 centimeters or 2 meters by 60 centimeters, respectively: diameter to height).

4
Next, proceed to the internal work. To the sink, bathroom, washbasin, kpripim siphons and sewer pipes. So that there is a natural stock, make a slope at least 0.25 centimeters per meter. Toilet with a corrugated pipe with a plastic tube, the diameter of which is 110 millimeters. We definitely do the hydraulic table so that there is no seeling smell in the room. Now we take a large pipe out.

5
On the street so that the sewage is not frozenTake care of depth promials Soil. Divals for sewage digging under a slope (2-3 centimeters per 1 meter of pipe length). Pour the pits with sand, only then lay the pipes. Well, if there are no turns to the sewer. In this case, the drain will not be clogged. If it is impossible to dig a trench below the level of the lands of the Earth insulation the sewage pipe of polystyrene foam or other insulating materials.

6
It remains to dig up the pit under the septicch and the team well. Septic tank is better to purchase ready, and there are such structures that the prefaby well and will not need. However, you can make it from concrete rings. To do this, in the already finished pit fall asleep sand and gravel. Lower the ring, the slots between the rings close up with a solution. It is in the septic tank that the sewer tube will enter. From the second hole, it is necessary to remove the pipe into the national well, where filtered water will be collected. The team of the pit is done, like septic, only the bottom of it is slightly higher in terms of the filtering well. Top of finished reinforced concrete structures Cover the round slab, and put the hatch on top to it.

It remains to have a test of ready-made sewage. On the pipe in the septica sweat the bucket. Go to the house and in the toilet pour the water bucket. If the suspended container in the septic is filled completely, it means that there are no problems with the drain.

Comments leave a comment
Tone 01/07/2015 at 14:47

At my own cottage, I did it myself, but when it came time to my parents. It was immediately visible where the pros was worked, and where I am.

To answer

Add a comment

Your e-mail will not be published. Mandatory fields are marked *

close