Vegetation on the face of men is associated with masculby and strength. But, not all men like to wear a beard, so they prefer regular shaving bristles on her face. The tougher bristle, the more difficult and more carefully it has to suffer. As a rule, ordinary machines with removable blades or electric shavers, which do not give the desired result, scratch the skin and cause irritation on it. The perfect weapon in the struggle of the bristles is a dangerous razor, which not only high quality and smoothly shaves the face, but also prolongs the term between the shave procedures - shave is less likely. The only minus shaving of a dangerous razor is that there is a high probability of cuts on the face and neck, therefore, before proceeding with the procedure, you need to master the shave technique and correctly choose the tool.
How to shave a dangerous razor - preparation of the instrument
The basis of the perfect shaving hazardous razor is a high-quality tool made of particularly durable metal. The razor must be as acute, do not have bends or any deformations. Only due to the correctly sharpened danger razor can be achieved perfectly shaved smooth skin, without irritation and scratches.
Tool sharpening to trust only a professional master. The process of sharpening a hazardous razor is quite specific and difficult, requiring special skills and experience. Right tools on the belt using a special paste, holding it at a certain angle. Visually determine the sharpness of the razor is impossible. There is a popular test for determining the sharpness of the blade. You need to fix the razor, the blade up and smoothly omit perpendicular to the hair blade. If, barely touching the blade, the hairs fall into two parts - the sharpening is performed perfectly.
How to keep a dangerous razor
There are two main ways to keep the tool:
- The first way. The tool is held in the brushes convenient for you, the blade down, the handle - up. The thumb should be restarted into the lower part of the razor, the left of the cutting edge. The little finger should lie on anonymous edge, being at the end of the razor - on the place of connection with the case. The remaining fingers are located on the edge.
- The second way. This method is considered more convenient. Take a razor in hand, blade up, handle - bottom. Position the little finger under the so-called tail (screw tool fastening to the case). The thumb should be from the inside of the inexpensive edge with notches, and all other fingers place from the outside.
How to shave a dangerous razor: stages of work
- Prepare the skin to shave. Moisten and raise face. You can use a warm, wetted terry towel, which is applied to the face for a few minutes. If the bristles are too tough - repeat the procedure.
- Apply foam on the face of shaving foam, thick layer. It is not recommended to use soap foam to shave the hazardous razor, it is better to use a special tool.
To shave did not cause discomfort from the touch of cold steel to the skin, lower the blade into warm water. - Start shaving on the right side, pulling the skin with your fingers with your left hand. The tool movements are aimed at the growth of the bristles and are performed head forward. Keep the tool at an angle to the skin surface 30-40 degrees. First, go through the blade from the temple down, moving towards the corner of the lower jaw, then move from the center of the cheek, directing the blade to the chin. The next stage - shave directed from the chin up, moving to the bottom lip, and then shave the zones of the mustache over the upper lip and side. Perform smooth movements with a blade along the edge of the face and go to the neck. It is important to pull the skin so that the blade goes smoothly and smoothly.
- After removing the bristles on the right side, go to the left side of the person. Be prepared for the fact that the procedure takes a lot of time and requires special accuracy and attention. It should be borne in mind that even the most acute razor is not able to completely remove all the hairs. Therefore, you need to walk the blade and against hair growth, after performing a repeated shave, but starting from the neck, moving up the corner of the lower jaw to the temple.
- The final stage of shaving is the removal of foam residues and washing the face with cool water. For skin prone to inflammation, you can apply a warm compress with a wet towel.
Shaving a dangerous razor requires a certain level of skill and experience. Newbies should be extremely careful and not to rush. Over time, the hand will become solid and confident. The main rules of the safe shaving of a dangerous razor - knowledge of equipment and rules, as well as the calm and the dimension of the movements performed.
0
568
