How to make a bird feeder from a plastic bottle?

At any time of the year, in parks, green courtyards, gardens you can see birds-feeds for birds. The number of improvised canteens increases with the onset of cold weather, and this is understandable - people seek to feed singing birds in the winter. Bird feeders are made of wood, dairy bags, candy boxes, disposable dishes, in general, from any suitable material. In this publication, we will tell you how to make a feeder from a plastic bottle.

1
How to make a simple bird feeder from a plastic bottle?

For feeders take bottles of different volumes, but the optimal container is 1.5 liters.

Need:

A bottle (1.5 l) - 1 pc.
Scissors
Scotch

We make:

Cut the hole in the center of the container (for the entrance and output of birds) and tighten its sharp edges with a sticky tape.
Tie a strong rope to the neck of the bottle (for fixing on the tree), pour the grain on the bottom of the container and the dining house is ready.
According to the same principle, a feeder of a five-liter bottle is made: cut the door, treat sections, put the food and fasten the stain by the maintenance handle.

2
How to make a feeder from a bottle and spoons?

For such an original craft, in addition to 1.5 liters of bottles and cutting tools, two more wooden flat (without painting) spoon will be needed.

Work steps:

On the one hand, set the container from the bottom of 10 cm, mark with a marker.
Turn the container by 90º and set it up from the bottom of 5 cm, indicate. Make through the stamps of the through holes and insert the spoons.

By the way: tablespoons should be located under an inclination and crossed in the center, then the structure will be stable.

Near the wide side of the spoon (scooped up), increase the hole so that the grains are freely rolling into a spoon.
Pour the food, close the container with a traffic jam, tie the wire to it and the dining room is ready.

3
How to make a feeder - automatic design

To build such a building, prepare:

A bottle of 5 l - 1 pc.
A bottle of 1.5 liters - 1 pc.
Scissors or knife

Important: pick up the container so that the smaller bottle can climb the “head” into a large one.

The course of actions:

In the largest container, build a hole on both sides - the entrances for birds.
Cut the bottom of the 1.5 liter bottles so that her throat does not reach the bottom of the five -liter - 3 cm.
Pour the grain into the eggplant, stick a small bottle into it with a narrow end, into which also pour the food.
Wrap a cork with a large container inserted into it with a rope and hang your invention into the garden.

4
How to make a feeder - horizontal option

Such a feeder is made in the same way as in the first paragraph, only the product turns out to be elongated horizontally.

Take:

Bottle for 5 liters
Knife
Marker or felt -tip pen

Started:

Draw on containers on both sides along the rectangle and cut them from below and from the sides. Bend the upper part - get a window with a visor.
Pierce a long baker with a horizontal bottle through - this is a nest.
In the floor of the feeders, for water and condensate, do several holes with a needle.
Bind one end of the rope by the neck, and the second - pass through the hole in the bottom. Pour the food and - the work is completed.

5
How to make a feeder from a bottle - an option with a plate

Also a simple way, but the device is comfortable and stable.

Prepare:

1.5 liter containers
The plastic plate is deep
Bolt with a nut
Burn

We proceed:

Make a bowl and holes in the middle and pull the parts with a bolt with a nut.
In the neck, pierce holes for feeding.
Pierce the hole at the bottom of the bottle and pull the harnesses folded in half over it.
Pour the food into the container, tighten the lid, turn the bottle and hang by the rope in the right place.

The presented feeders are not difficult, so you can work on them with a child. And most importantly, no matter what the mechanism you master, the birds will appreciate it and will be happy to eat the proposed treat.