Each motorist before or after the acquisition of his iron horse thinks about the garage, safer in all parameters - from hacking, from natural whims, etc. The walls can be well strengthened, on the garage gate to hang a few durable locks with a secret, but the roof should be pounded by special technology with one of the many roofing materials.
1
If the garage is in the garage cooperative, then the standard dimensions approved by the Cooperative Commission will most likely be allocated for it, and the roof design should be made according to the generally accepted sample - single one. The same roof design can be done at the garage attached to the wall of the house. The duplex roof of a separate garage looks more familiar and allows you to use additional space under the roof for your needs.
2
The question "what the roof of the garage is" is important in the roof. The slate roofs are rapidly come into disrepair and with mechanical exposure quickly deformation (stone, a tree branch can break through the slate, which will lead to the flow of the roof), metal roofs of the road and require additional funds against condensate. The roof covered with reinforced concrete plates with the upper layer of rolled guided materials is the most reliable, but requires the cost of renting a crane when installing the plates.
3
The most economical and lightweight in the device is a roof of slate or professional flooring. Such an option of the roof can be used for a garage in your own yard, in the garage cooperative such a roof will require additional safety measures of the car. If the roof design is single, then for the right roof, it is necessary to calculate the difference between the height of the opposite walls and to withstand this difference when the garage wall is erected. For example, if the width of the garage is 3 m, then the difference of wall heights should be at least 75 cm (3 m * tangent angle 14 ° \u003d 3 * 0.2493 \u003d 0.748 m).
4
On top of the side garage walls, the support beams fall on, which will serve as a support for the beams of overlapping and rafters. The support beams are attached to the anchor bolts with a diameter of 12-14 mm, which are drilled in advance in the walls (from 3 anchors per supporting beam). For a convenient and durable overlap clutch with walls, you need to drill the grooves in the appropriate places in the support beams. Before laying the support beams (Mauerlatov) on the top of the walls you need to put two layers of the rubberoid so that they do not rejoice from the clogging moisture. Tighten the beams.
5
On top of the support beams are required to put rafters. The distance between the rafyles depends on whether the roof insulation will be further (for standard insulation slabs - 60 mm). In the calculated places of laying, the rafter needs to be cut out the grooves (45-50 mm). Bashed rafters better than two nails directed at an angle towards each other.
6
On the rafters, see the crate of the board. It does not matter whether it will be a edged or non-edged board. The density of this layer is also unimportant. The main thing is that the nailed boards can be laid waterproofing (runneroid). The insulation flooring is required from the lower edge of the skate to the top with the overlap of the upper layer of the lower. According to the same technology - the bottom-up material is also stacked. If slate is used as roofing material, then it is necessary to mount it with slate nails to the cut in the crest of the wave. If the professional flooring is required on a layer of waterproofing to put an additional layer of doom for ventilation of the condensate formed.
7
It is desirable when laying sheets of professional flooring to have sheet size equal to the size of the roof of the roof. The standard sheet of professional flooring is manufactured up to 12 m long. For fasteners, experts advise to use selflessness with a washer from neoprene, which are attached to the collapse of the profile.
8
The emptiness and holes between the walls and the roof must be laid with mortar and brick. The upper edge of the roof cover the skate (curved profile) to protect the wooden roof design from snow, rain and other humidity.
If the roof is chosen for the roof of the roof using wooden components, do not forget shortly before laying the roof to treat them with a special antiseptic and flame retardant impregnation. All roof roof work should be carried out in dry weather.
0
2127
