InDesit washing machines error codes - Characteristics

In the washing machines Indesit, when faults appear, an error code is displayed. Each code has its meaning and possible troubleshooting.

• The code "F01" is a notification of a short circuit of a thyristor controlling the engine. To solve this problem, check the presence of water leakage on the internal wiring. It is also possible to closure on the terminals of the engine.
• The code "F02" signals the engine lock or closure, or the absence of a connection in the chain of the tachogenerator. If the test showed that the engine is not blocked, then inspect the contacts of the J9 connector on the winding of the tach generator located on the board: Measure the resistance of the conclusions 1 and 2 (the norm is 115 ohms - 170 ohms), ring them. If the engine is in a three-phase washing machine, then check the presence of a chain between 6 and 7 output on the j9 connector. If the problem persists, then replace the engine.
• The "F03" code indicates a circuit violation on the NTC sensor or the shading on the power switch. Check the contacts on the j8 connector: on the NTC temperature sensor, measure the resistance between 11 and 12 by the connotes of the j8 connector (at 20 ° C in the room - 20 com). If the result is different, then connect the j8 connecting J8 and the NTC sensor. Replace the temperature sensor if necessary.

• The code "F04" - the sticking of the pressure switch in the "emptying" position leads to water overflow, the drain pump will turn on automatically, the result is active two signals: "emptying" and "overflow".
• Code «F08» - sticking relays PETN when a signal "emptying" or sticking of the pressure switch in the "fill" if there are signals "emptying" and "overflow". Additionally prozvoniv 5 and 6 of terminals on the connector J3. Replace the pressure switch.
• Code «F10» - at the same time the signals of "emptying" and "overflow."

• Code «F05» - blocking the drain pump or the pressure switch malfunctions. Inspect connector J9: between 8 and 9 pin voltage must be 220 V. Check that the supply to the pump, the pump filter and clean the drain. Replace the pump.
• Code "F07" - the absence of current consumption at Tan signal "emptying". Check the contacts of J3 connector: rung 5 and 6 terminals. If the heater has characteristics of 1800 W and 230 V, the resistance should be 25 ohms. Check the J3 connector on the algorithm «F04» code. Replace the heater and / or pressure switch.

• Code «F13» - NTC sensor circuit is open. Check connector contacts J10: prozvoniv wire on the connector, the resistance between the 7 and 8-pin connector at the room temperature of 20 ° C should be 20 ohms. Replace the NTC sensor.
• Code «F14» indicates that the sensor is connected drying or heating element circuit is not closed. Check the contacts on connector J2, the characteristics of the resistance heating element 1300 W and 230 is 40 ohms. Inspect the drying heater and connecting the connector J10. Replace the heater.
• Code «F05» - sticking relay contact drying or short circuit thyristor drying. To solve the problem, first check the contacts on the connector J2 and the wires that connect it with the TAN drying and pressure switches.

• If a code «F09», pointing out an error in the program, replace the memory card (ESPPPZU) or check the installation.
• If no feedback signal from the pump or motor winding is disconnected, the display appears «F11» code. In a conventional system, lock the washer door checks should resistance between 1 and 2 J15 connector terminal, and when the lock system Easy Door - between 8 and 9 J9 connector. It should be 170 ohms. Check the wires at the pump. Replace the pump if the detected discrepancies.
• If there is no connection between the main board and the display board, the «F12» code appears. Prozvoniv wires that connect the display board (5-pin) connector and J11.
• If the washing machine is vertical loading, then the drum lock is possible. In this case, the error code is "F16".
• With the traditional door blocking system, it is possible to open its chain. The corresponding code is "F17". In this case, if the machine in standby mode, then the voltage between 2 and 3 is missing, and between 1 and 3 - is 230 V. Check the door latch. Replace the lock mechanism.
• The error code "F06" is not in the brands of AVD and AVL washing machines.

If the measures taken did not solve the problem, then replace the fee. The same action must be performed and when an error appears with the code "F18", which indicates an error of communication between the signal processing device and the microprocessor.