Any motorist wants his "Iron horse" to always look at the highest level, but sometimes dents and other similar defects (most often they are a consequence of an accident) appear on a careful and thorough care of the car. Fortunately, they can be eliminated themselves, and by the way, it is decent to save at the same time - the local body repair at the one hundred today is not suiced.
1
A little-free shallow dent on the doors or hull of the car can be easily easily and quickly eliminated with the help of a special construction dryer and a compressed air cylinder. Getting Started, thoroughly clean the defective area from dust and wipe dry, dismantle the noise insulation and door trim, raise the glass as much as possible. After that, it is well warm the desired part of the body with a hairdryer, then direct the jet from the cylinder to dent. Under the pressure of the air, a slight recess will disappear within a few seconds. Perform work in protective rubber gloves.
2
To eliminate the deare dent, you will need a conventional hammer and mall (hammer with a round rubberized head), a small wooden bar and a clean soft rod. Before starting work, completely disassemble the internal trim and dismantle the automotive door to get the maximum access to the damaged surface from the inside. Armed with a rubber hammer, start carefully straightening flawed with light tapping movements (strong blows may entail a sprinkling of paint coating). If the irregularity is not amenable to straighten, wrap the wooden bar with a cloth, attach it to a defective surface and tapping it alternately on it with a rubber, then the usual hammer until completely eliminating irregularities.
3
One of the most effective options for self-eliminating the dentin on the wing and the car case is considered to be Richt. For the utility work you will need a jack (hydraulic or wheels), a special stripping hammer, various extension cords, powerful emphasis and several wooden bars. Before the direct elimination of body flaw, dismantle the wheel with the appropriate side of the car. After that, under the jack of the jack. Place a strong emphasis. Further, put the first bar under the wing right on the edge of the rigidity, the second bar - in the back of the automotive wing. Then the appropriate extender is put on the jack and place this design between wooden bars. Start swing a jack as well as when lifting the car - at this time the air breaks the wing, so that the dent is stretched. Fixing the jack, carefully verify the groove, gently tapping the hammer on it from the inside of the wing (at the same time apply support to the outside of the wing). Important nuance: Start such repairs with rigidity ribs and only then proceed to rattling other damaged sites! Upon completion of the work, it is not recommended to immediately relax the jack, it is better to be slightly tightened to avoid the wing deformation.
4
You can align the dent with the help of a non-professional device for self-elimination of body defects - suction cups with thermoclaim. The kit of this simple device includes a special glue and a gun for heating it, a few suction cups of different diameters, a bridge-bracket and a spatula for removing glue. The gun will warm the glue, apply it to the surface of a suitable suction cup (pick it up in the size of dents). Then the suction cup is glued to a defective area, and after full soaring glue, fasten the bridge-bracket on it. Next, neatly tighten the bolt on the bracket until it straighten the irregularities. After that, remove the sucker and carefully squand the spatula of the leaks of glue. During the alignment procedure, dents are important not to drag the metal so as not to damage the paint coating of the car.
5
You can eliminate a small dent on the wing of the car with a football / basketball ball with a camera and a conventional cycling pump. Place the ball with a pre-lowered chamber between the defective surface and the frame. After that, start slowly pumping the ball - gradually folling with air, it "painlessly" for paintwork lines a unwanted dent. After eliminating the irregularity, lower the ball and carefully remove it. Consider that this method is suitable for straightening small dents that do not affect bodybuilding ribs.
6
Also small deepening without beggars and fragilated edges (motorists call them "clams") can be pulled out with a conventional powerful magnet. Attach it to the edge of dents and start pulling on yourself (at the same time smooth motion, move the magnet from the edges to the central part of the defective area). To avoid damage to the paint, between the magnet and the car body, be sure to put a soft tissue napkin.
Following our instruction, make a small body repair of your "iron horse" even a beginner motorist.
0
2286
