How to use a glue gun

Adhesive thermopystoles increasingly began to be used in everyday life. The tool has won its popularity with a light design that allows you to achieve a solid connection in a short time. Ease of operation in conjunction with cheap consumables make the device indispensable.

To achieve the maximum effect of application, it is necessary to properly use the adhesive pistol. This will ensure not only good work, but also will prolong the service life of the instrument.

1
How to use a glue gun - construction and work principle

Before you start using the thermopystole, it is necessary to clearly represent how the device is arranged and what is necessary for its operation.

In the form, the device resembles a gun, from which it got a name. The hull is made of heat-resistant plastic, which facilitates the weight of the device.
The design provides a handle for which you need to keep the device. Depending on the size of the model, there are recesses for the fingers.
Power supply from a standard 220 W power outlet. It is possible to connect to the generator. Some tool brands have a built-in battery.
Glue is inserted into the device through a special hole on the back of the tool. It has a shape of a tube of different diameter, depending on the model of the adhesive gun.
Inside the housing is a heating element that melts the rods.
The heating time of glue is different in each individual type of device, and ranges from 3 to 7 minutes.

2
How to use a glue gun - preparation for work

The principle of operation of such devices is the same, but it will not be superfluous to look into the instruction manual. Perhaps your model has a number of features.

Since this is an electrical device, then inspect the housing for damage. Even a small crack on plastic can lead to trouble.
Also pay attention to the nozzle. If it is clogged or in it there are other pollution, then clean it. Otherwise, the glue will not be able to pass through the channel.
Take the glue rods of the required size for your device. It also happens a different length. It will not affect the operation of the device. If the tube gives you an inconvenience, then cut it down.

Advice. There is glue of different colors. Select it into the surface of the surface, which is supposed to glue.

Insert the glue into the connector on the back of the device until you stop. The next rod add after the first was completely spent.
Move the stand that is located on the tool housing. Or buy separately. Be sure to check the stability of the location of the thermopystole on the table.
Scatter the cord, connect the tool to the outlet. If its length does not allow you to freely use the device, then use the carrying.
On the case, turn on the switch. This element allows you to adjust the degree of heating of glue and the time of operation over different elements.

Important. The heat chamber warms the glue not immediately. She will need a time that depends on the power of the heating element.

On the readiness of the use of the device will tell you the indicator. If this is not in your model, then slightly press the lever. The device can be used in the presence of droplets of glue on the nozzle.

3
How to use a glue gun - work process

When all preparatory actions are completed, proceed to the instrument. Proper use of technology guarantees an effective result.

Since the glue is not heated immediately, so it should not be pressed on the trigger when the device is turned on.
While the thermopystole is heated, prepare items for gluing. Their surface is cleaned of contamination and fat spots.
Adhesive volume Adjust push strength on the lever. You will find it on the handle. Squeeze a strictly necessary amount. Excess adhesive is difficult to cut in a frozen form.
Clay hot retains its temperature for 10 seconds. During this time, apply it, and press the parts together. The greater the adhesive, the more time required for its hardening.
If you are working with a few interruptions, then mount the unit on the stand. Since the glue gun will be in a tilted state that will not allow the hot glue zatech inside the mechanism.
Keep track of time when the device is included. Do not exceed the indicated duration of its continuous use. So professional models can work up to 2 hours, and the technique for creativity is 20 minutes.
When you need to fix multiple items with breaks, a thin web appears during gluing. Remove it easily in the frozen state.
After completing the work, wipe the tip from the remnants of the glue. Use for this paper or soft tissue.