How to put linoleum on old linoleum

Often, the ordinary manner postpones repair work for an indefinite time, since it, to put it mildly, confuses the preceding destruction throughout the dwelling, referred to as preparation and accompanied by a large number of dirt and dust. Especially with the arrangement of the new floor. The prospect in this case does not please - dismantle the entire design to a rough base. But if you deal with linoleum, it can be treated without specific preparatory work, right on the old linoleum.

Laying linoleum on the old linoleum is permissible, although many experts recommend to remove the remnants of the material before work, and in some cases has good arguments "for":

The presence of an even base that is convenient for the installation of a new floor covering.
Easy preparation for work, which consists mainly in cleaning the floor from garbage.
No need to lay a substrate that costs a lot.
No need to dismantle an old coating.

Before direct installation, it is necessary to estimate the state of the base, the floor surface for laying linoleum must meet several requirements:

There should be no strong plane drops that make up 2 mm. After all, the new coating will repeat them all, breaking through.
Also unacceptable the presence of such defects, both pyles and waves, breaks and cracks, protruding and sharp elements. But the abrasion of the role does not play.
The coating should be rigid, smooth.
It is impossible to drain the material on the wet, too cold linoleum if the temperature differences are observed.

When choosing a linoleum for flooring, give preference to thick coating or material with a substrate so that it does not break through. Also possible is a variant of a separate styling of the substrate. Given the fact that linoleum is homogeneous and heterogeneous, commercial, semi-commercial and private application, it is better to choose a homogeneous commercial coating. However, it should be remembered for a non-democracy price and the possible appearance of white strips during operation, which is particularly often happening when laying on the old linoleum. To prevent this, you need to competently evaluate the material when buying: Make a sharp bend at its tip, it should be not a white strip on it, but the same color as the coating itself.

Methods for connecting linoleum cloth:

Welding. The method is suitable when using a linoleum without a substrate. Two pieces are adjusted tightly to each other, eliminating the appearance of gaps. Under them it is necessary to put a dense cellophane, do not forget to mark it with glue, for example, PVA. Then you need to place a newspaper on top of the seam, which warms up a preheated iron as a press.
Hot welding. It will take a professional construction hairdryer and a special nozzle in which the linoleum gluing cord is refilled. To do this, make a rubber on its width, putting subsequently in the seam.
Cold welding, type A. In a slot formed between two linoleum slices, you need to pour a special adhesive composition that has a liquid consistency. When it is frozen, a monolithic compound is formed.
Cold welding, type C. The technique is similar to the use of cold welding type A, but suitable for gaps that are less than 4 mm in size.

The procedure for laying a linoleum on an old coating is as follows:

At the first stage, preparatory work must be prepared. To begin with, remove all the furniture from the room, remove the floor plinth and connecting strips if they are present. If there are widespread cracks, they should be filled with silicone sealant. Then this surface must be processed using a rubber spatula. Prepare such tools and materials: stationery knife, primer composition, glue for cold welding, gloves to protect hands, greasy tape. Also required glue: PVA, latex.
Engage reveal material. Best of all, if you are able to cover the whole room in one piece. Otherwise, you need to cut the linoleum so that the number of seams turned minimal. For smooth edges, use a sharp knife and a ruler made of metal. Note that between the wall and at the strip should remain a gap. Nesting cover, leave it in the room for several days, to lie down, and it has taken the required position.
Begin gluing linoleum flooring with it on the surface, taking into account the pattern of linoleum. Thus it is necessary to control the absence of debris between layers. Bend the piece of the wall, to be applied to the underside of the adhesive. If the base surface is smooth, use a latex if fleecy - need a PVA. For applying the adhesive take trowel. Fluff portion flat on the floor, followed remove all air bubbles that formed by smoothing. If this is not done, then the linoleum sheets will slide over the surface of the warp and, when it will go.
Now we proceed to grouting. First, they are cleaned and degreased. Once at the joint that was formed during the linoleum flooring, fasten and causes masking tape adhesive for cold welding. When the glue is dry, and it will happen after half an hour, remove the tape. Attach the floor plinth.

This method is best suited when laying linoleum on the old linoleum.