The laminate has heard a fairly aesthetic coating that successfully imitates the wooden floor. It is inherent in a democratic price, and it is easily stacked, as a high-quality lock system is provided. However, besides such tangible advantages, the operation of the laminate is associated with some inconveniences. It must be mounted on a qualitative basis, as it will begin to behave unpredictably - to creak, troce and hurt. And this is no longer a joke, it annoys! What to do in this case?
1
Uneven base. In the case of a poorly prepared surface, the laminated coating will be creaked only in certain areas where the holes occurred. It is over them that the laminate saves and begged when a person comes to him. At the same time, sounds are published. Therefore, it is always worth paying attention to the alignment of the draft floor under the laying of the coating.
Solution:
If all this trouble happened, then try to correct the situation: disassemble the laminate until you find a problem space, squeeze the hole with a solution or launch the cardboard sheets, then the coating is placed in place.
With stable sounds from all sides, nothing remains to you, except to fully disassemble the laminate, numbered its dice to simplify the subsequent assembly. Then you have to remake the base, the bulk floor is best suited for this.
2
Thick substrate. Many owners believe that in the case of buying and laying too thick coverage, it will be possible to level the differences. But such a material will only aggravate the problem, laminate kept stronger in areas with pits. Remember that the substrate thickness should be at least 2-3 mm. What to do: you need to disassemble the floor, get a thick substrate and replace the base to thin, aligning the base.
3
Small gap, which is formed between the coating and the wall. When laying a laminate between it and walls, a clearance must be provided for at least 7 mm. With a large area of \u200b\u200bthe room, it is done more - 2-3 cm, given the width of the plinths. It is necessary that the coating can dispense and take the desired position to prevent the embroids. With the laminate laminate too much, the expansion is strengthened into the walls and will publish loud sounds. To solve the problem, remove the plinths, then reduce the extreme coating boards to the gap formed. After that, the plinths put back.
4
Delta of humidity level. Laminate is an outdoor coating that reacts sharply to moisture drops. It creates when it is raised, besides all the floor surface. When the humidity is normalized, the sounds disappear. As a rule, this inconvenience disappears in itself. And over time, the laminate adapts to the installed microclimate. But if the creak does not pass, you will have to completely remove the coating, search for irregularities, to lay this floor again or shut down a new one.
5
Sand and dust. Laminate requires careful care and removal of dust using a vacuum cleaner. But it should also be done at the stage of its laying, controlling that there is no garbage between the films and the base, which provokes the hollow of the floor and causes the laminate locks. If there is a need to saw up the boards, do it in another room. How to proceed. The sand is considered a fairly serious problem when you have to fully disassemble the laminated coating (do not forget to numbered the dice). After you need to take the screed, cover it with primer and put a new substrate. In case of doubt, place a polyethylene film on the tie for the substrate.
6
Bad material. When using poor-quality laminate, you are not insured against various kinds of surprises. It can tripping in locks even when complying with all requirements and technology, as they have low quality. Unfortunately, in this case only the complete change of coverage and laying a new, better quality will help.
7
Voltage in locks. This reason is the most common when the laminate crepts totally. After laying, the coating begins to change the position, "picking up" the optimal, adapt to the basis, as if to "swim". When the position is found, the screens are leaving along with a voltage in the locks. It lasts such a process from 7 days to several months. Thus, do not be afraid of light hollows at first after laying. But if six months later, the laminate still eats sounds, it's time to look for another reason.
Do not forget about the whimsicalness of such a simple laminate look! The reasons for the symbol considered above should be taken into account even at the stage of laying a laminated sex in order to prevent them further. Do not forget that before the workflow, the material must "acclimatize" in a new place - for 3 days. This moment can also trigger the screens, so do not drop from accounts and it.
0
1069
