How to make a slant?

The needlewomen are often wondering what a slanting bake is and how it can be done. Everyone who knows how to work on a sewing machine will be able to cope with the task. Let's take a closer look at what a slanting bike is a failure, why it is needed and how to do it if necessary.

1

The essence of the oblique fake

In order to run out of various elements of clothing, they make a slanting base (a strip of fabric in this case is cut out along the oblique). Thus, the seamstress will be able to carefully arrange the neck or any neckline on the dress.

Of course, you can buy a slanting bike already in the finished form, but in fact you should not spend money on this purchase, because any seamstress will be able to make it with your own hands without much difficulty.

First you need to prepare for the process in question, in this case you can’t do without preparatory work:

• We determine what material we will use for this for cutting. This is the first thing you will have to do in the situation under consideration. There are no strict recommendations or prohibitions. You can use for such purposes such as the main fabric and fabric with any pattern.
• When various elements are processed, our oblique laying can form a strip, both on the front side of the product and sit on the wrong side. In the first case, it is better to use the fabric thinner, and in the latter, on the contrary, more tightly.
• If we talk about statistics, then in this case, the oblique layer has a width from 2 to 4 cm (mainly). If the slanting base is located on the front side, its width must be larger than Kant, and more precisely, then wider, four times. If we talk about accurate calculations, then the length of the box is calculated as follows - to the length of the edge, which is processed, 4 centimeters (maximum) are added.

2

The design of the box

It must be understood that the slanting bike may also not be integral. That is, its design can consist of several parts. They are usually connected obliquely, so that the connection angle is at least 45 ⁰. In this case, it is necessary to pay attention to the accuracy of the connection, because the optimal option is to make the box so that the seams from the joints are in places where they will be invisible.

After the cutting process has been performed, it is necessary to iron the box (this is a mandatory rule). This must be done along its entire length, and in the beginning - in half, and only then with cuts inside. Such work without exaggeration can be called painstaking, so it will be difficult with this process that will be only inaccurate and unassembled needlewomen.

In order to make it easier to iron the box and do this at a time often use special devices. They can be both with their own hands and production. It is clear that the latter will need to be purchased for money or there is an option to ask a twin or girlfriend of a needlewoman if she has this device in stock.

Before proceeding with the processing process, it is necessary to make sure that all seams are made as expected. In the event that Kant turns out to be in care or negligence on the front side of the product, the allowance will have to be cut in any case, if the box is located on the back, you do not need to remove the allowance.

3

Choking me scraping

To begin with, you will need to find a piece of fabric so that its shape is rectangular, and then we do the following:

• We fold this piece in such a way that a triangle is obtained, that is, the fold will go diagonal. Now it will be necessary to mark the fabric with oblique lines so that these markings are parallel to the bend made obliquely. Here you need to immediately decide on the width of the box, because this size should already be taken into account at this stage.
• Now it will be necessary to cut off the fabric along the last and very first line. All that is superfluous must be removed from the field of view so that triangular pieces do not interfere with us. For example, take 5 strips of la our box.
• The next stage - with a pencil, mark 6 mm from the edges (lower and upper). Now we draw horizontal lines from the marked points. The fabric will need to be folded so that the front side is inside. Ultimately, on each of the sides, the fabric should go beyond their borders.
• The next step is to shake the fabric with small invisible fabric so that all the lines painted obliquely coincided with each other.

• Now it's time to turn on the machine and sew the material on the planned lines (where we fastened it with needles).
• We are believing in the allowances, and it is necessary to do this so that they look in different directions.
• We take scissors and cut our fabric obliquely, right along the previously drawn line, and to the end.
• We fold the resulting strip twice, and the wrong side remains inside, after that it will be necessary to iron the fabric. The element must be expanded and bend inside with the existing cuts (you need to do this to the bend). After the process done, iron again.
• We fold the fabric twice again, the field of which we repeat the process to iron.

So you got a scumbag, and did not even have to spend money on its purchase. The process, in principle, is simple, only you need to understand it in more detail. It is for this that you are given the instructions above, in which everything is described in detail.