How to make a dress pattern

Clothes stitched with her own hands - bears originality, individuality and uniqueness. With the help of independently designed design, you can try yourself in the image of a fashion house of fashion.

1

How to make the pattern of dresses - measurements

If the design is defined and the material is selected, you can proceed to the most important stage - removal of measure.

The main measurements for the pattern:

• Breast girth - measurements are carried out according to the most protruding points of the chest.
• Girth over the breast - the measurement is made over the chest glands.
• Waist girth - measured by narrow location.
• Hips girth - measured according to the most convex places on the buttocks, if there is a halife, it is necessary to measure and in this area.
• The height of the chest is the distance from the neck to the shoulder to the spectacle point on the chest.
• Length transfer to the waist.
• The length of the product is in the case of the dress - the sterling from the seventh vertebra on the neck.
• The width of the back.
• Width shoulders.
• Length shoulders.
• Cooking hands and depth of the armor.

These are the main measurements for building the dress pattern. Measures should be carried out centimeter, tightly pressing it.

To go directly to the drawing of the product, you need to decide on the silhouette of the dress. From this indicator, the values \u200b\u200bof the increases for sizes and further calculations will depend.

To build the pattern of the adjacent silhouette, you need to calculate the following indicators:

• Spin width - the eighth of the gripping of the chest plus 5.5 cm.
• The width of the armor is the eighth of the grip of the breast minus 1.5 cm.
• Breast width - from a quarter of breast girth take 4 cm.
• The depth of the armor - for a reliable result it is better to measure.

2

How to make a dress pattern - building patterns

• On the prepared paper it is necessary to position the point and at the top. From it to postpone the vertical line corresponding to the length of the product and put the point D. to postpone the segment of the half of the gripping of the chest plus 1.5 cm to the right from the point A - to put the point V.
• On the cut, hell measure the depth of the armhole plus 1.5 cm - points r and g1 (on the segment B-C) \u200b\u200bto connect the horizontal line.
• In the AVGG1 rectangle, on the segment of Mr.1 to postpone the width of the back, the width of the armor and the width of the chest (all the necessary additions to these indicators were taken into account on the segment A-B). Lower the waist line - from the point and down to postpone the segment equal to the length of the back to the waist - the point of T. to connect the horizontal line of the T-T1 point.
• From the point of the waist to postpone the height of the thighs, refer to the point L and pave the horizontal line L-L1. From the middle of the width of the armor on the segment of Mr.1 to postpone the vertical line - the middle of the sides.

• Next, you should build the back of the neck of the back - from the point and postpone the segment equal to the neck of the neck, and lift the point 2 cm. Connect with a point and the curved line. On the auxiliary line of the armor, on the left - to postpone the segment equal to 1.5 cm down and connect to the end of the neck. The lower point of the shoulder of the back and the middle of the armie to combine the curved line.
• To remove the neck of the anterior shelf, from the point G1 to postpone the length of the segment equal to the fourth part of the chest girth plus 0.5 cm. The line of the armor is transferred to this height. On this line, to postpone the left segment long to a third of the neck of the neck, outline the neck of the front shelf.
• When building the shoulder of the front shelf, it is necessary to take into account the shading. For this, from the top point of the neck to build a sloping short line to the left. From the end of this line, carry out a perpendicular cut down and move it to 1 cm to the right. From this point, spend a cut up under the tilt, as if connecting the continuation of the shoulder line. Continue the shoulder line, speaking for the right auxiliary line of the shelf by 2 cm. And to connect the figure line with the middle point of the armor.

• The size of the side extracits for such a model is to calculate - half of the semi-coupling of the breast minus half half-coupling the waist. The resulting number distribute on the side shades and attachment to the waist. Machings on the back and sides turned out a little wider than on the front shelf. According to the middle lines, they watched the pump, considering the type and curved figure.

So, to achieve the correct construction of the pattern, before starting it is necessary to clearly imagine the silhouette and the simson of the future product.

It is also necessary to practice and view the alleged schemes before starting the pattern of the pattern.