How to remove the protective glass from the phone

How to remove the protective glass from the phone

The main goal of the protective glass for the smartphone is to protect the screen from drops, shock, scratches. Such a glass can serve for a very long time, but over time, chips, cracks, scratches appear on it and deteriorate not only the appearance of the phone, but also its functional abilities - the angle of the smartphone is reduced, the sensor may incorrectly operate. In this case, you need to remove the old glass and stick a new one, but the removal process is not the easiest lesson, if you do not know all the nuances.



1
What will take to remove the old protective glass from the phone

Remove the glass without having nothing at hand, almost impossible. And if the usual film can be picked up with a nail and dispose, then with glass such a number will not pass. You will need:

  • medical gloves - preferably, but not necessarily;
  • flat object, such as plastic card or mediator;
  • alcohol-containing wiper or other alcohol-containing substance (vodka, cologne, perfume, etc.);
  • muffard napkin;
  • silicone sucker - preferably.

With such a set, remove the protective glass from the screen of the smartphone will not be easy, and the whole process will take 5 minutes. Often in the set with protective glass already have all the necessary devices.



2
How to remove protective glass from the phone - precautions

Protective glass and smartphone screen are two perfectly smooth surfaces that are very firmly glued together, and the reason for the electrostatic forces (in rare adhesive exceptions). To spare them from each other simply using a flat object (for example, a knife) is almost impossible, but there is probability to seriously damage the smartphone.

It is also unlikely to remove the protective glass with one suction cup alone, although there are more chances than in the case of a knife. If the glass is damaged, then most likely that the suction cup will simply bounce without any effect. This is at best. In the worst case, the sensor will go away from the body, and then you will have to change the entire phone matrix that it will cost very expensive.

3
Remove the old protective glass from the phone

  • First of all, put on the gloves on your arms, or if there are no thoughts of your hands with soap and wait until they dried. It will relieve you from extra divorces on the screen.
  • Find on the glass the most whole angle, if it is damaged, away from chips and cracks, and embrete a suction cup there.
  • Under the glass in the corner where the suction cup is located, insert the card or the mediator. In order for this to be done, slowly and smoothly pull the suction cup, but not sharp, otherwise you can disrupt the sensor or the entire screen. If there is no suction cup, then try to make a gap carefully with a card.
  • Next you need to smoothly promote the card inland, peeling the glass. It is necessary to do it slowly if the screen is very large (for example, on the tablet), then it is better to work at the same time with two three cards.
  • When the glass was almost completely dug, pull the suction cup on itself and it will go away.

As you can see, this is not a very complicated procedure, the main thing is to follow the rules.

4
Glue new glass on the phone screen

  • When the old glass is liquidated, you can proceed to the process of sticking a new one. It is necessary to do it with clean hands in not a dusty room. Wash your hands thoroughly, clean the phone screen with alcohol-containing liquid and take a new protective glass.
  • Remove one film from the other side to be glued directly to the phone. Keep the glass as close as possible to the surface of the phone. Thoroughly align it, make sure that all the holes fit, and only then completely lower the glass on the screen.
  • If bubbles appear, they can easily be out, having spent a dry cloth on glass. The last step is to remove the second film, and your phone is protected.

And remove, and stick the protective glass is quite simple, and for this it is not necessary to contact the mobile salons, everything can be done quickly with your own hands.

Comments leave a comment
Leonid 04/15/2017 at 6:05.

Useful info. thanks

To answer
Mikola. 04/17/2019 at 20:36

Stopadovo crookedly stick! We must not remove the protective film to put the glass on the smartphone screen, then a pair-three pieces of scotch glue it to the housing with one of the sides, and to the other glue one piece. Then holding a glass to the side for it, while the tape from the other hand will perform the role of "door loops"))) Clean the screen, remove the protective film from the glass and taking the glass for a single piece of scotch lower on the smartphone screen. Voila, glass is glued perfect!

To answer

Add a comment

Your e-mail will not be published. Mandatory fields are marked *

close