How to change the turn signal light bulb

The owners of the car are simply obliged to know the design of their car and all the processes occurring in it, because the details are a huge set, and therefore, someday, each of them may fail. Today we will talk about such a detail as the Lamp of the Laminator and find out how to replace it if necessary.

1
Replacing Turning Light Bulb

Turning These are important elements in any car (in principle, not important details do not happen in this mechanism, as in any other). After all, it is thanks to them, the driver shows the rest of the participants of the movement of their maneuvers - in this case we are talking about turning.

To enormous regret, in modern cars, the light bulbs in the turn signals are not so rarely, which leads to the lack of a signal sign during the commission of the next maneuver on the roadway. In this case, the replacement of such a detail becomes mandatory, and the faster you do it, the safer you will move along the road and will become safe for the rest of the movement.

To begin with, let's look at how to replace the bulbs in the turn signa of the front block of the headlight. The scheme of this process is simple, so how to cope with your own hands with this process will not be any difficulty:

At first, the driver must be mandatory to turn off the ignition. With this procedure should begin any process that the driver wants to start in the car.
Open the hood. It is best to fix it so that further actions produced in the repair process were completely secure for the driver or the one who will deal with the replacement of that light bulb.
The next stage is to find the chain bulb bulb under the hood, take up of it and immediately turn them counterclockwise to get it. It should be noted that you need to remove the cartridge together with the light bulb, so it is necessary to get it carefully and not in a hurry.
Contacts in this case do not need to be disconnected - this is an important point in the process under consideration.
It is clear that you will need to get a light bulb in advance or first get the lamp from under the hood, go with her to the store and buy a similar, but working and new.
Now it's time to insert a new light bulb into place of burnt. We do it too carefully, insert into the recess for the bulb of the turn signals and scroll it clockwise, screwing it on the spiral.

So in several movements you can quickly get the burned paw and change it to a new one.

2
Side repeaters of turn signals

If you have burned down the light bulb in the side repeatters, then it will be necessary to replace it as follows:

First you need to remove the side repeater. To do this, you need to push it slightly, not more than 5mm.
After that, pull it out the back of it, which is under the wing. Now you will need to get a side pointer.
The next step is to get a rubber cover, the border is in the opening of the front wing.
Pay attention to the fact that the cartridge and the case are needed at the same time.
Now just listen a light bulb, which burned out and put a new one in her place.
Installing all parts is made in the reverse order.
Only a few steps and the light bulb in the side repeater is changed to the new one.
Now let's figure it out in detail how to replace the turn signal lamps in the lamps, which are located behind the car:
In order to carry out this process, first will need to pull the board at the rear head.
Only after that the driver will have to get a light bulb, which burned out, and put a new one in her place.
As it was possible to notice from the above information, the replacement of the turn signal lamp The process is very simple, will cope with which everyone who has never even engaged in the repair of his car. There is nothing complicated here, the main thing is to know the sequence of actions that should be taken into account for the timing replacement of such light bulbs.

3
Rules for replacing turn signal lamps

There are a number of rules that must be observed when changing the bulbs of turn signals:

First of all, always turn off the car, that is, the ignition should be turned off under any circumstances.
The light bulb must be selected in accordance with the old option, which is subject to replacement. If you cannot determine the type and type of light bulb visually, then you first have to take off the light bulb and go to buy a new one.
The whole process of replacing the light bulb should be carried out carefully and not in a hurry, so as not to spoil with their actions no other details in the car.
In any type of car, all the bulbs turnover are screwed and twisted very simple, without a special effort. It should be understood that the light bulb is very easy to thread and if this process is not so easy. So you do something wrong. The reasons can be a lot - he rusted the spiral, which means it must be cleaned or the lamp is not suitable, which you are going to put in the turn signal.

If you unlocked the turnover yourself and found that there are any contamination from them obligatory, it is necessary to get rid of, and immediately, do not leave everything as it is, because such a statement can negatively affect the work of the turn signal itself.

If the light bullet in the turn signal burned - not the trouble, because it is even more difficult to change to a new one, especially if you carefully familiarized with this instruction.