How to finish knitting caps

How to get down or add a loop, how to finish knitting - these are the questions that beginner knitters often face. We will understand in the wisdom of the right completion of working on the headdress.

There are several ways to crochet knitting:

The easiest method is to start working on top, after performing a round bottom and continuing to knit for the desired length, and complete it with a rubber band or other decorative border.
If you knit the headdress "from below", then the simplest option is to do the so-called "pipe" the main pattern of the desired length, close the last column or air loop and gently sew the product from the inside. In this case, you will receive a classic "cockerel".
When you make a product that will wear a child or a mischievous teenager, you can sew two corners, slightly retreating from the edge, and then you will have a fashionable hat with ears in your hands.
Another way is to pull the top, sew and decorate with a bubonic or brush.
Alternatively, it is possible to raise a more elongated pipe and tear up with it with a decorative knot, retreating from the end of about five to seven centimeters, thus forming an interesting brush from the capped cap itself.

Please note that these listed ways are suitable not only for crochet, but also with knitting needles.

When knitting a cap with knitting needles for the manufacture of the bottom, you need to learn to accumulate. Digit loops must be started after checking about a third of the depth of the header. There are two ways to accommodate: with the formation of wedges and without. In the first case, divide the number of hinges for eight (six or four - depending on the desired amount of wedges). If you do not have an integer - do not be discouraged. Just add "extra" one or two loops to any clina. Now make the accumulation at the beginning of each segment, just tissing together the two first loops. The accumulation is carried out, as a rule, in every fourth row, but it can be less likely, and more often, depending on the size and shape of the head. When you will remain on the knitting on the knitting on the knitting of each wedge (there are two in some - in the event that you received a non-integer when divided), take a needle with a thread and sew all the loops together.

The second method does not imply the formation of wedges. After ready for about a third of the caps, start to subscribe every sixth loop. That is, in each row every five loops, there are two together. In the last five-seven rows, we immediately reduce three three, that is, tie together the fifth, sixth and seventh. When you reach the desired length, you do not close the spokes on the spokes, but carefully, by one thread and form the top. If desired, it can be decorated with a pompon or brush. The most difficult thing is to make a feedback for a hat with a pattern. Unfortunately, there are no uniform recommendations. Therefore, either finish the product using the options described above for the tube cap, or produce the "to the eye" to the eye so that the image is not shifted.

To make her own bubo, you will need quite a bit effort. To do this, cook threads, cardboard and scissors. Fold twice the sheet of cardboard and draw a two concentric circle on it, the diameter of which depends on the desired pompon size. The average size is 10 and 5 cm. Cut the two figures similar to the bagel, fold together and begin to wipe the thread, passing it through the inner hole. Wash the thread while the place remains inside. Now scissors gently cut the yarn on the outer circumference, tie the thread between cardboard bagels and remove them. Make sure the node is tightened as hard as possible.

To make a brush, you will need the same materials: cardboard, threads and scissors. From the cardboard, cut the rectangle slightly more than the length of the future product (if desired, you can use a thin book or brochure). Cut the thread that later will be the basis of the brush, put it on top of the cards and start to unwind the yarn from the main ball. After you wog the required quantity, make the basis for the nodule, delete the base and cut the winding. The thread on which the brush holds, lower down and, holding it for it, turn the brush. Carefully distribute the threads and tie them up, a little retreating from the base. Wrap the craft several times, secure. Hang the edge of the resulting brush.