We all know that "the main thing that the suit sat". How to achieve the perfect suit boarding? You can make it long and pickily choose it in the store, but you can bet on the win-win option - to sew a suit yourself. To do this, select the appropriate fabric, the desired pattern and attach a little effort. We'll figure it out how to properly sew perfect pants.
1
Before you start, you need to choose a model that is suitable for your type of figure. Modern fashion provides a wide selection of interesting models, but when sewing trousers, it is recommended to pay attention to classic models suitable for all types of shapes. These are straight pants of the middle width with an arrow, trousers with a low waist, with an extension from the hips or tights from above, with a slight expansion from the knee. If you sew pants for the first time, choose models without pockets.
2
Now let's go to the choice of fabric. Of course, first of all should take into account the season, during which you are going to wear new things. Wool is suitable for winter, flax or silk - for hot summer. Velvet trousers dictate a sporty style, TVID will be appropriate in official events.
3
At the next stage, proceed to measurements. Follow some rules: the measurements are removed by a measuring tape, not a ruler. The volume of the waist is measured by the finest place, the volume of the hips - on the most convex places of the buttocks, pay attention to the presence of a hailife. The length of the trousers is calculated by side from the waist line to the floor, the height of the seating is measured sitting, placing the tape strictly vertically from the waist line to the surface of the chair.
4
Gently fold the cloth in half and decompose on a flat surface. For confidence, undercase pins. You can use a dining table or even the floor. Remove the two front and two rear halves of the trousers and the belt.
5
What seams perform the first? Think if you want to stop the side, internal or step-by-step seams. If so, then start with them. In trousers without a delay it is advisable to start with side seams, then stepper, the last stage is performed internal. Step seams are kept the greatest load during operation, so it is necessary to give them additional elasticity and strength. On a non-professional sewing machine, this can be achieved with a double lines. Please note, on dense tissues, the lines should be made in exactly each other, and on loose tissues - closely.
6
After performing side, internal and rear seams, proceed to the zipper processing. Carefully burst the front seam before the fastener starts. Purge inside, freeze and join the slap. Please note that on the left side of the fastener should be left around a centimeter behind the line center line. The left front half the trousers are accrued close to the tooth along the edge of the cut on the zipper bracket, step up.
7
Remove trousers, scroll the place of the future clasp. Slow from the face right half of the fastener, facing the slip. After that, stick to the wrapper with the right half of the trousers to the lightning tape and push. Please note that the front-halves of the trousers at this stage are not needed.
8
We will proceed to design a belt. To the invalid side of the in advance of the outlet Iron, skid a special fabric - Flizelin or Dublerin. Attach the belt to the trousers with the facilities of each other, freeze and push. Do not forget to leave on the left side of the allowance on the seam, on the right side - the allowance on the seam and the fastener. Raise the belt up, enter. Remove to the involve and start a break on the seam along the entire top cutting of the belt. Fold the belt inside the front side, take the belt ends. Remove the ends on the face. Print the inner edge of the belt and the trigger of it manually by a secret seam.
9
The last stage - we like pants on the bottom. The easiest option is to use a special tape - adhesive cobweb. To do this, add about 1.5 cm to the desired trouser length, turn it out and glue the cage using an iron. However, this method is only suitable for trousers made of light fabric. In pants made of more severe material, you can perform a conventional double bending. Measure the desired length of the trousers, add 2-3 centimeters, begins 1 cm, the mark is laid, followed by one more 1 cm, throwing and paving the line from the front side.
10
Classic Pants for Official Cases Line Using Broken Tips . So, measure the desired trouser length, we add 4 cm. We do the bottom edge of the trousers. From the front side, impose a brain so that its edge goes out for the lower cut of the trouser at 0.1-0.2 cm, the ends of the braid should be left on the other, laid the line in the braid. Turn the trousers to the required length and swing the secret stitch.
As you can see, tailoring the trousers - the task is not from the lungs. It is necessary to pay special attention to detail and have skills to work with patterns and sewing machine. Start with simple models, work out the sewing of individual items - and one day you will easily save your perfect pants.
0
2486
